ANSI, 1999. — 13 p. This standard provides a system for uniform visual acceptance criteria for surface imperfections on rolling element bearings used in aircraft engine, engine gerabox and accessory applications.
ASTM, 2004. — 3 p. This guide contains good practices for the selection, training, qualification, and professional development of personnel performing analysis, calibration, physical measurements, or data review using nondestructive assay equipment, methods, results, or techniques. The guide also covers NDA personnel involved with NDA equipment setup, selection, diagnosis,...
ASTM, 2009. — 5 p. This practice covers general requirements for the establishment and maintenance of a quality management system for agencies engaged in nondestructive testing (NDT).
ASTM, 2009. — 33 p. This standard defines the terminology used in the standards prepared by the E07 Committee on Nondestructive Testing. These nondestructive testing (NDT) methods include: acoustic emission, electromagnetic testing, gamma- and X-radiology, leak testing, liquid penetrant testing, magnetic particle testing, neutron radiology and gauging, ultrasonic testing, and...
ASTM, 2009. — 7 p. This guide establishes areas for review and provides a survey form that can be used in determining the competence of a nondestructive testing agency.
ASTM, 2007. — 9 p. This guide is intended to assist in the integration of ergonomic principles into the design and planning of new occupational systems from the earliest design stages through implementation. Doing so may reduce or eliminate the necessity for later redesign that could have been foreseen.
ASTM, 2009. — 4 p. This terminology describes and illustrates imperfections observed on whitewares and related products. For additional definitions of terms relating to whitewares and related products, refer to Terminology C 242. To observe these defects, examination shall be performed visually, with or without the aid of a dye penetrant, as described in Test Method C 949....
ASTM, 2007. — 11 p. The purpose of this guide is to present methods and techniques for the visual inspection of electrical protective rubber products. This guide also includes descriptions and photographs of irregularities found in these products.
ASTM, 2009. — 3 p. This practice is intended to serve as a guide for determining specific inspection requirements for marine surface preparation and coating application during new construction, major retrofit, or routine maintenance contracts.
ASTM, 2009. — 11 p. This document provides guidance on the implementation of risk assessment and risk control for Process Analytical Technology (PAT) processes within the pharmaceutical industry. Wherever possible, other appropriate standards on risk assessment/management have been referenced and acknowledged. Where practical, further details of methods and additional...
ASTM, 2010. — 6 p. The purpose of this guide is to establish a framework and context for process understanding for pharmaceutical manufacturing using quality by design (QbD) (Juran, 1992;2 FDA/ICH Q8). The framework is applicable to both active pharmaceutical ingredient (API) and to drug product (DP) manufacturing. High (detailed) level process understanding can be used to...
American Institute of Aeronautics and Astronautics. — Approved October 2010. — 141 p. — ISBN 978-1-60086-784-2. This standard provides guidelines for selected reference and standard atmospheric models for use in engineering design or scientific research. The guide describes the content of the models, uncertainties and limitations, technical basis, data bases from which the...
ASME, 2013. — 464 p. The ASME Section VIII Division 1 Example Problem Manual (PTB-4, 2013 edition) provides practical examples based on the 2013 ASME B&PV Code, Section VIII, Division 1, aiding in understanding and applying the code's rules for pressure vessel design and construction. The American Society of Mechanical Engineers Foreword Acknowledgements General Requirements...
ASTM International, 2006. — 11 p. This guide identifies factors relevant to the quality of language translation services for each phase of a translation project. The guide is intended for use by all stakeholders, with varying levels of knowledge in the field of translation.
AMT, 2004. — 84 p. This document provides ergonomic design guidelines intended to improve quality, performance and safety by reducing fatigue and injury associated with manufacturing systems, including individual and integrated machines and auxiliary components. It is intended to be a resource that can be applied to: a) Design or major modification, installation and use of...
Society of Automotive Engineers, 2002. — 57 p. SAE JA1012 (“A Guide to the Reliability-Centered Maintenance (RCM) Standard”) amplifies and clarifies each of the key criteria listed in SAE JA1011 (“Evaluation Criteria for RCM Processes”), and summarizes additional issues that must be addressed in order to apply RCM successfully.
SAE International, 2009. — 18 p. The Physics-of-Failure (PoF) is a science-based approach to reliability that uses modeling and simulation to design-in reliability. This approach models the root causes of failures such as fatigue, fracture, wear, and corrosion. Computer-Aided Design (CAD) tools have been developed to address various loads, stresses, failure mechanisms and...
Society of Automotive Engineers, 1976. — 4 p. Historically SAE has been concerned with nomenclature as an integral part of the standards development process. Guidelines for automotive nomenclature were written in 1916, were last revised in 1941, and were included in the SAE Handbook until 1962. The present diversity of groups working on nomenclature in the various ground...
American Institute of Aeronautics and Astronautics, 2009. — 39 p. This standard establishes uniform requirements and criteria for a performance-based, product Failure Mode, Effects and Criticality Analysis (FMECA). The performance-based aspect of this standard requires that the organization's FMECA capability be rated according to predetermined criteria for process capability...
American Institute of Aeronautics and Astronautics, 2009. — 30 p. This standard establishes uniform requirements and criteria for a performance-based anomaly detection and response (ADR) analysis process. The performance-based aspect of this standard requires that the organization's ADR analysis capability be rated according to predetermined criteria for process capability and...
American Institute of Aeronautics and Astronautics, 2001. — 74 p. This Recommended Practice is a collection of techniques for managing parts programs. It addresses the preferred program elements adopted by the aerospace industry (military, civil, and commercial) for parts management. The approaches cover electrical, electronic, and electromechanical (EEE) and mechanical parts....